|
Home
Introduction
Contact Info
1911 Custom Pistols
Browning Hi-Power
Smith & Wesson Revolvers
Finishes
Photo Gallery
Terms
Grips Links
Holster Links
Testimonials
| |
SMITH & WESSON CUSTOM REVOLVER SERVICES
Full services are offered on what I believe to be one of
the finest double action revolvers made - Smith & Wesson. Services
available include accurizing and action/trigger work for purposes from
carry/defense to competition.
|
Revolver Action Work |
| Carry Action Job (J-frame) - Action tuned for
smoother & lighter trigger pull. Includes: set cylinder end shake; smooth cylinder rotation; set cylinder
headspace, check barrel/cylinder gap; check timing (additional cost if
correction needed); polish action contact
surfaces; set spring tensions. |
$100.00 |
| Deluxe Action Job (K,L,N frame) – Action tuned for
smoother & lighter trigger pull. Includes: align yoke, center pin &
ejector rod; set cylinder end shake; smooth cylinder rotation; set cylinder
headspace, check barrel/cylinder gap; check timing (additional cost if
correction needed); polish action contact
surfaces; set spring tensions. |
$115.00 |
| Competition Action/Accurizing Job (K, L, N
frame)- The ultimate
revolver!!! A competition action/accurizing job combining techniques
learned from Jack Weigand and Ron Power (and a few tricks of our own!). Includes: All items listed in the Deluxe Action
Job plus additional detailing of every action component for a silky smooth
action: competition pull weight spring settings; forcing cone recut; barrel
recrowned; trigger rounded and polished; internal trigger overtravel stop;
yoke ball detent; cylinder chambers chamferred. Barrel set back at additional
cost if required. This package is legal for IDPA
and ICORE. |
$295.00 |
| Round & Polish Trigger Face |
$30.00 |
| Install Internal Trigger Overtravel Stop |
$25.00 |
| Remove Hammer Spur and Convert to Double Action
Only |
*$55.00 |
| Correct Firing Pin Protrusion |
$30.00 |
| Detail Strip (complete disassembly), Clean,
Lube & Inspect |
$25.00 |
|
Revolver Cylinder Work |
| Correct Cylinder End Shake (may require barrel
set back which is not included) |
$25.00 |
| Straighten & Align Yoke |
$25.00 |
| Straighten & Align Ejector Rod |
$30.00 |
| Retime Cylinder (parts not included) |
$40.00 |
| Install Oversize Cylinder Stop (part not
included) |
$40.00 |
| Install Ball Detent in Yoke (includes parts) |
$25.00 |
| Chamfer Cylinder Chambers |
$25.00 |
|
Revolver Barrel Work |
Shorten Barrel & Modify for
Weigand Interchangeable Front Sight
System
(This work can only be performed on heavy walled barrels with raised sight
ribs.) |
**$145.00 |
| Set Barrel Back to Correct Excessive
Barrel/Cylinder Gap, Recut Forcing Cone |
**$80.00 |
| Correct Insufficient Barrel/Cylinder Gap, Recut
Forcing Cone (must be done in addition to end shake correction) |
$35.00 |
| Recut Forcing Cone |
$25.00 |
| Recrown Barrel Muzzle |
*$30.00 |
|
Revolver Metal Work |
| Convert Square Butt to Round Butt (smooth strap
only) (customer must provide grips) |
**$95.00 |
| Dehorn Entire Revolver for Carry |
**$50.00 |
| Stipple Back Strap (on existing smooth back
strap) |
*$40.00 |
|
* Minor refinishing - will be cold blued. ** Complete
Refinishing Required. |
All prices listed in the service schedules are labor only for work performed
on your firearm and do not include parts or materials unless noted otherwise.
All prices and specifications are subject to change.
|